tag:blogger.com,1999:blog-8968604820003269863.post1729899561997352507..comments2024-03-21T03:05:46.528-07:00Comments on Chemical & Process Technology: Saturate Dry Gas With Water in HYSYSWebwormhttp://www.blogger.com/profile/11991072858350648438noreply@blogger.comBlogger5125tag:blogger.com,1999:blog-8968604820003269863.post-73677495933000182762018-03-27T00:39:28.465-07:002018-03-27T00:39:28.465-07:00Hello, I am one of your website customers. I want ...Hello, I am one of your website customers. I want to thank you for all your post and particularly this post on your website. You are doing the best job. And I wish you good luck. <br /><a href="http://smartdigitalwork.com/digital-marketing/search-engine-optimization/" rel="nofollow">Seo Services In Delhi</a>Seo Services Company In DelhiAnonymoushttps://www.blogger.com/profile/13819552360082693419noreply@blogger.comtag:blogger.com,1999:blog-8968604820003269863.post-50895177997740247142010-05-22T08:47:22.247-07:002010-05-22T08:47:22.247-07:00It works.It works.JoeWonghttp://webwormcpt.blogspot.com/noreply@blogger.comtag:blogger.com,1999:blog-8968604820003269863.post-12674286515574781492010-05-22T01:16:11.913-07:002010-05-22T01:16:11.913-07:00Dear all,
i have another method. I need inputs if ...Dear all,<br />i have another method. I need inputs if this is correct. <br />Mix the the dry gas stream with water stream at same process conditions. there might be a dip in temperature, so add a hypo heater. Then separate the gas and liquid water(excess) stream with two phase separator. Then check for the water at the bottoms of the separator. Add an adjust operation to the stream after hypo heater and the input water stream. Set the target value for HC stream as 0.9999 vapor frac. and adjust the mass flow of water that is input to mixer. <br />That should also work.<br /><br />Regards<br /><br />DhirajUnknownhttps://www.blogger.com/profile/04065051873114266676noreply@blogger.comtag:blogger.com,1999:blog-8968604820003269863.post-69516857499523480302008-11-07T15:35:00.000-08:002008-11-07T15:35:00.000-08:00Muhammad,Thanks for your comments.You may set the ...Muhammad,<BR/>Thanks for your comments.<BR/><BR/>You may set the Wet gas at required temperature and leave the Water temperature free. The Water temperature will be adjusted automatically by HYSYS module so the Dry gas temperature same as Wet gas temperature.Webwormhttps://www.blogger.com/profile/11991072858350648438noreply@blogger.comtag:blogger.com,1999:blog-8968604820003269863.post-43672002700744915412008-11-07T13:31:00.000-08:002008-11-07T13:31:00.000-08:00Dear all,Nice article regarding dry gas saturation...Dear all,<BR/><BR/>Nice article regarding dry gas saturation. But, in my opinion there must be a 2nd adjust function to keep wet-gas [saturated gas]temperature same as the dry gas has. In existing model gas temperature will decrease as we add water contents to it [owing to heat energy requirement for evaporation of water droplets to saturate the dry gas].<BR/><BR/>Best regards.<BR/><BR/>Muhammad Adnan Hanif<BR/>Process Engineer<BR/>Fauji Fertilizer Company Limited<BR/>adnan_hanif@ffc.com.pkAnonymousnoreply@blogger.com